| |
The Global Positioning System (GPS) is most widely known as a system for vehicle and marine navigation. However, each GPS satellite orbiting the earth also has an integrated precise atomic clock that can be used as a reference clock for NTP time servers and for general computer timing applications. This article describes the components required to utilise GPS for computer timing applications. It also discusses how the GPS system can be used for computer network timing by using the Network Time Protocol (NTP) and NTP time servers.
The GPS system is a United States military system intended for global navigation. The GPS system is a space-based system, consisting of a network of 24 orbiting satellites. Precise navigation and positioning is achieved by utilising precision timing signals and triangulation between multiple satellites. In order to provide very precise time, each satellite has an integrated highly accurate atomic clock onboard. Each satellite broadcasts timing information to within a few nanoseconds of the correct time to provide positioning to an accuracy of better than 10m. This precise timing information can be used by NTP time servers and other computer timing equipment as a highly accurate time reference. The great thing about GPS is that it works anywhere in the world and is entirely free to air service.
Each GPS satellite transmits a low-power radio signal down to the surface of the Earth. Two separate frequencies are utilised, designated L1 and L2. The L1 band is the civilian signal; transmitted at 1575.42 MHz. L2 is the military frequency, intended for ultra-high precision positioning. The radio signals are transmitted from the satellites by line of sight. The transmitted signal is easily powerful enough to pass through clouds, glass and most plastics but is absorbed by more substantial material such as brick, roofing materials and metals. The ideal location for a GPS antenna tends to be outdoors and ideally on a rooftop with the best possible view of the sky.
In order to receive GPS timing and positioning information some relatively low-cost equipment is required. A GPS antenna is utilised to receive and amplify the GPS radio signals. While a GPS receiver decodes the information and presents it in a computer readable format. Many antennas are available with integrated receivers but these have the drawback of only providing a few meters of cabling to the host NTP time server or computer system. Rugged GPS marine antennas screw down on to a rigid threaded pole mount able to withstand the worst of the weather. These antennas provide the best solution for static timing applications.
The GPS receiver is generally embedded into the NTP time server or encapsulated within an enclosure. GPS receivers are small modules that have a connection to the GPS antenna to receive amplified GPS signals. The receiver decodes these signal and provides a computer readable output usually via a RS232 or USB interface. Typically, information provided by the receiver includes time and positioning information, number of satellites in use, number of visible satellites and whether a signal lock has been acquired.
Coaxial cable is utilised to provide a connection between the GPS antenna and receiver. The cable distance can be critical. The antenna must amplify the GPS signal sufficiently to overcome any cable losses associated with the cable run utilised. Better quality antennas generally provide more amplification (gain) additionally higher quality coax cables can be used with much smaller signal losses per meter allowing for relatively long cable runs between a antenna and receiver. In order to extend cable runs still further GPS amplifiers can be used to boost the signal transmitted down the coax cable. Typically, a GPS amplifier sits in-line on the coax cable and is powered from the receiver. Multiple amplifiers can be used for extremely long cable runs.
A roof mounted GPS antenna can be prone to lightning strikes and voltage surges. It is recommended that surge suppressors are utilised to protect expensive NTP time server and timing systems from potential damage. A surge suppressor is essentially a barrier that sits in-line on the coax cable between the antenna and receiver that protects the receiver from any potential damage due to voltage surges.
To summarise, the GPS system provides a highly precise timing reference for NTP time servers and other computer timing equipment. It is a reliable free to air service that can be used anywhere in the world. Additionally, with the boom in vehicle navigation systems the technology required to receive GPS broadcasts is continually falling in price.
The author, David Evans, is a technical author in the field of computer network timing systems. David has a number of years experience of writing articles and white papers about NTP and GPS time synchronisation. Click here to visit our web-site if you would like more information on NTP Time Server systems.
 EasyPublish™ this article - publishers click here
More articles by David Evans
- What to Look For in an IP Camera Enclosure (Wes Fernley)
IP camera enclosures help keep your IP camera safe from the elements of weather and vandals who would destroy the camera at any given chance. This article will discuss what to look for when purchasing an IP camera enclosure. - Looking for Products that Sell on eBay (Jenny How)
looking for profitable products to sell on ebay - Using an IP Network Camera to Monitor Your Home (Wes Fernley)
With security being a topic on most peoples' minds, many wonder what the best way is to monitor their home and belongings. Various security systems exist and using a combined home security system with surveillance cameras can add extra protection against intruders.
|